You might be able to get a grip on the head with a pair of needle nose pliers and turn it that way, to make some extra room you could take a knife and carefully scrape some plastic off around the hole. You need just enough room to grip the screw shank with locking pliers and twist it out. If only one of the screws is stripped, you can try removing all other screws first, then twist the motor out, it should work even with loctite. If it keeps slipping, try pressing it down with one hand. I have an ASUS N550JK and I’m trying to open it up because the screen keeps flickering on and off, but it appears that one of the screws is stripped. For long screws or drywall holes, plug the hole with a dowel rod of the same size. Use a smaller drill and drill a hole into top of the screw.
Rubber Band – This screw removal method is done by putting the rubber band over the stripped screw. For wood or drywall, coat screw threads with beeswax for easy removal. One of the least expensive extractors seats a collar over the stripped screw then uses an extractor bit to pull the screw out. When you can feel it bite into the metal, keep turning it counterclockwise and pull to remove the stripped screw. Remove the other screws, desolder the motor from the ESC now instead of trying to rotate the screw with your screwdriver, hold the stripped screw with you thumb and rotate the motor instead of the screw this time. Fortunately, there is a specialized tool for screws that are size 12 and larger: a screw extractor. If the extractor breaks off in the screw, it may require a professional to finish the job. If the nut is flush on the screw, this shouldn’t be a problem.
As it is screwed into the stripped screw, the counterclockwise rotation casues the screw to back out of its hole. Use a hammer and tap the screwdriver gently to the screw head. 5. Place a fine chisel under the screw head and hit the chisel with a hammer. Drill a small hole into the center of the screw head. Drill Head Off Screw – Use a drill and as a last resort, drill the head of the screw completely off. Alternatively, you could spot weld or solder the nut and screw together. JB Weld and a screwdriver or bit you can stand to lose. Having no dremel tool, no super glue, no pliers I settled on hammering a small indent on the screw (with a flathead screwdriver) so it could grip the flathead screwdriver while I was slowly turning it. Sometimes the rubber will give you the extra grip needed to get that screw out. I have tried: I have tried the smallest screwdriver that will fit in the tiny hole and nothing will move. Maybe your pilot hole is too small or you didn’t drill a pilot hole at all. Use smaller pilot holes for small screws and deeper pilot holes for larger screws.
Removing stripped screws requires plenty of time and patience. Removing a stripped screw involves using both ends at the extractor bit. Start by picking the right size extractor bit for the screw you’re removing and then chuck it into your drill driver with the burnishing end facing out and switch your drill drivers transmission to reverse. The rubber material will help fill in the gaps of the stripped screw and provide enough grip to turn it. Once the glue or adhesive is dry and set, use a wrench to turn the nut and hopefully it will hold and unscrew the screw with it. A bit of super glue on the end of the torx let it dry, don’t spill it everywhere! Insert the plug into the hole with the smooth end up. This method works by opening up the hole to allow you to get deeper into the screw to unscrew it. 1. Put a rubber band over the stripped screw. Depending on how stripped it is, putting a rubber band between it and the driver may help.
Now flip the driver bit around to the extractor side and keep your drill driver set to reverse just like the burnishing step. If the extractors threads don’t want to bite down into the screw head, you may need to switch back to the burnisher and drill down a little bit deeper to clean out even more of that waste or switch to one extractor size larger than the one you use and try that instead. Clean up jagged edges with a ½-inch drill bit. It kind of looks like it’s just a circle with no edges. They’re double-ended hardened steel bits and this end of the bit actually looks a little bit like a conventional drill bit. Use a ½-inch drill bit to drill down just far enough to reach the broken end of the screw. How to remove a stripped T5-Torx screw from a laptop? 2. While keeping a tight grip, rotate the screw counterclockwise to remove it. If the screw is rusted or in metal, spray it with penetrating oil and wait 15 minutes before proceeding. With a set of extractor bits like these, you can fix the problem in a few minutes and be back to work again.